library not working with espressif32 esp32-s3 Arduino core > 2.0.14

[Jason2866]

Device crashes at boot.
Open issue in Arduino repo espressif/arduino-esp32#9618 (comment)
and
Xinyuan-LilyGO/T-Dongle-S3#26

[thelastoutpostworkshop]

I confirm, esp32-s3 reset under 2.0.16 (when init is called), when installing espressif arduino core 2.0.14 works fine

[jfseaman]

I confirm, under 2.0.14 it works for ESP32-C3, ESP32-S3. I did not test ESP32 but same code.

Under 2.0.15 and 2.0.16. Software reset breaks. Actual code from TFT_eSPI_ESP32.h TFT_eSPI_ESP32_xx.h is:

#define SET_BUS_WRITE_MODE *_spi_user = SPI_USR_MOSI
and
#define SET_BUS_WRITE_MODE *_spi_user = SPI_USR_MOSI | SPI_CK_OUT_EDGE

"Guru Meditation Error: Core 0 panic'ed (Store access fault). Exception was unhandled."

[jfseaman]

The issue persists under 2.0.17.

[ats3788]

I use PlatformIO
[env:my-esp32]
platform = espressif32 @ 6.7.0
For further exploration of configuration options for the espressif32 development platform, refer to the documentation.

Supported Frameworks
Arduino - v2.0.16 (based on IDF v4.4.7)
ESP-IDF - v5.1.2
I don't even connect the ILI9341 to the board and it reboots

Rebooting...
␀�ESP-ROM:esp32s3-20210327
Build:Mar 27 2021
rst:0xc (RTC_SW_CPU_RST),boot:0xb (SPI_FAST_FLASH_BOOT)
Saved PC:0x4202934a
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fce3808,len:0x4bc
load:0x403c9700,len:0xbd8
load:0x403cc700,len:0x2a0c
entry 0x403c98d0
[ 112][V][esp32-hal-uart.c:330] uartBegin(): UART0 baud(115200) Mode(800001c) rxPin(44) txPin(43)
[ 121][V][esp32-hal-uart.c:416] uartBegin(): UART0 not installed. Starting installation
[ 129][V][esp32-hal-uart.c:463] uartBegin(): UART0 initialization done.
Guru Meditation Error: Core 1 panic'ed (StoreProhibited). Exception was unhandled.

[ats3788]

#define TFT_ESPI_VERSION "2.5.43"
#define ILI9341_DRIVER // Generic driver for common displays

#define USER_SETUP_ID 70
// See SetupX_Template.h for all options available
#define ILI9341_DRIVER

                // Typical board default pins - change to match your board

#define TFT_CS 10 // 10 or 34 (FSPI CS0)
#define TFT_MOSI 35 // 11 or 35 (FSPI D)
#define TFT_SCLK 36 // 12 or 36 (FSPI CLK)
#define TFT_MISO 37 // 13 or 37 (FSPI Q)

// Use pins in range 0-31
#define TFT_DC 7
#define TFT_RST 6

[cmachsocket]

i met the problem too.
I use 2.0.17 and esp32s3,and the program will reboot when it run tft.init()

[StuartsProjects]

Same here too;

https://github.com/Bodmer/TFT_eSPI/issues/3346#issuecomment-2143324416

A program to transmer images over LoRa and display on a TFT was working on core 2.0.11, but stopped when I updgraded the core.

By going backwards with the cores I found the last one that worked was 2.0.14. For later core versions the program would crash on start.

ESP32S3, Arduino IDE 1.8.19.